How Often Should You Change Hydraulic Fluid in a Log Splitter?

May 31, 2023

We hope you love the products we recommend and just so you know that as an Amazon Associate MyLogSplitter may earn from qualifying purchases.

Hydraulic fluid is a liquid used to operate parts of machines, such as log splitters. Hydraulic fluid is stored in a reservoir and sent to various machine parts.

Checking hydraulic fluid on a log splitter is essential to maintaining your equipment. The oil can become milky and dirty over time and cause operation problems or even damage the equipment itself.

How Often Should You Change Hydraulic Fluid in a Log Splitter?

You should change the hydraulic fluid in a log splitter every 12 – 18 months or if it is beginning to look milky and dirty.

How to Check Hydraulic Fluid on your Log Splitter

To check hydraulic fluid on your log splitter, follow these steps:

  • Turn off the machine.
  • Remove any wood or debris from the splitter’s hydraulic system before checking hydraulic fluid levels. This will help prevent leaking and damage to other parts of the machine if any debris gets into them during the removal or installation of new components.
  • Locate the reservoir for hydraulic fluid in your log splitter’s tractor unit (TU). This will be on top of a large metal plate attached to the back of the TU’s engine block assembly (EBA). The reservoir may also have other components, such as hoses or lines that run across its surface for additional connections between various components inside your machine.

How to Drain Hydraulic Fluid for Log Splitter

How Often Should You Change Hydraulic Fluid in a Log Splitter?

Hydraulic fluid is used to operate the hydraulic system of the log splitter. It’s essential to drain hydraulic fluid for the log splitter before you perform any maintenance on your machine. Hydraulic fluid has a very high viscosity and will cause damage if it gets into your machine. How to drain hydraulic fluid for log splitter, Follow these steps to drain hydraulic fluid from your log splitter:

Turn off the power to the machine and remove all electrical cords and cables from the area where you will be working.

Remove any debris clogging up your machine’s hydraulic lines by loosening any large bolts or screws holding them in place.

Using a wrench, loosen all clamps holding hoses and lines in place on the inside of your machine. This is an essential step because it allows you to easily remove old hoses without damaging them or causing any leaks during this process.

Carefully disconnect each hose from their respective ports on your machine using plastic wrenches or large handsaws. Make sure you don’t damage any hoses or wires while doing this step!

How to Add Hydraulic Fluid to Log Splitter

Add hydraulic fluid to your log splitter by opening the tank cap and allowing the air to escape. Then open the valve on top of the log splitter, insert a plastic tube into the main chamber of the log splitter, and then insert another plastic tube into a port at the bottom of the tank.

Next, slowly add hydraulic fluid to these two tubes until they are complete. It is unnecessary to close either nozzle to add hydraulic fluid. When you are finished adding hydraulic fluid, use one of those plastic tubes you just inserted to siphon any remaining hydraulic fluid out of your splitter’s main chamber. How to add hydraulic fluid to log splitter:

  • Turn off the power and allow the machine to cool.
  • Remove any clogs in the hydraulic system by removing any debris or foreign objects that may be lodged inside it.
  • Open up the front cover of your log splitter and remove any debris that may have fallen into its hydraulic system while running.
  • Remove any obstructions from each cylinder head, such as dirt, leaves, or other debris that might be blocking them from working correctly.
  • Make sure that all cylinders are clear of obstructions before adding hydraulic fluid into them; otherwise, they will not be able to function correctly when you use them again for splitting logs later on down the road!

How Much Hydraulic Fluid Do You Need to Add to Your Log Splitter?

Logs are one of the most common materials used in your log splitter. They are also one of the most difficult to split, primarily when you must simultaneously split a large number of logs. You must use the right amount of hydraulic fluid to get the maximum performance out of your log splitter.

However, there is no exact amount of hydraulic fluid that you should use for every log splitter. How often should you change hydraulic fluid in a log splitter, the type and size of your log splitter will determine how much hydraulic fluid is needed. The best way to determine how much hydraulic fluid should be added is by testing it out first on some smaller pieces of lumber. If this works out well, you can increase your ratio until it does not work anymore. There are several ways that you can test out different amounts of hydraulic fluid before adding them to your system:

You can add small amounts until they work correctly and then increase them gradually until they stop working well. This works well with most types of logs because their sizes and weights tend to be inconsistent.

What Happens if You Don’t Change Hydraulic Fluid?

Hydraulic fluid is an essential part of the braking system, and it’s easy to take for granted. However, if you don’t change your hydraulic fluid regularly, your car’s brakes will not perform as well as they should.

You rely on your brakes to slow down or stop your vehicle safely when driving down the road. But if you don’t change your hydraulic fluid regularly, your brakes won’t work as well as they should. This is because the old fluid can build up in the system and cause problems when it is time for new fluid to be added.

You should check your brakes every few thousand miles for any discoloration or other signs of wear on the brake pads or rotors. If there are obvious problems with them, make sure that you get them checked out by a mechanic immediately so that they can be fixed before anything serious happens!

The most common error when changing the hydraulic fluid is not changing it. Many people think they can save money by not replacing their old fluid all at once, but this will cause you to lose function in your vehicle. You need to change the hydraulic fluid in your vehicle; if you fail to do so, you could experience problems with your brakes and steering system.

What Is the Best Hydraulic Oil for a Log Splitter?

Hydraulic oil is a blend of synthetic and petroleum-based oils designed to lubricate and protect mechanical parts. Hydraulic oils are used for many applications, including engines, transmissions, and other components requiring high vibration levels and heat. Hydraulic oil is also used in hydraulic systems such as power steering, valves, and pumps. When choosing a hydraulic oil, you have several options:

  • PETROLEUM-BASED LUBRICANTS: Petroleum-based lubricants are the most common type of hydraulic oil on the market today. These oils contain mineral oils along with synthetic additives and emulsifiers to improve their performance over time. Petrochemical additives such as polyalphaolefins (PAOEs) help reduce friction by reducing the surface tension between moving parts during operation. These additives also help prevent corrosion on metal surfaces, making them suitable for use in marine applications with tremendous saltwater exposure.
  • SYNTHETIC LUBRICANTS: They have become increasingly popular over the past few years because they offer better performance than petroleum-based oils while being more environmentally friendly than traditional mineral oils. They also provide better resistance to extreme temperatures and high pressures.

Wrapping Up

Log splits come in numerous shapes and sizes. How much work you still need to complete depends on what type of log splitter you are working with. There are many different types of log splitters in the market, each with its purpose and target audience. Considering this, one must consider what types are available before purchasing one.

We will be happy to hear your thoughts

Leave a reply